ZBA Z-3080 Manual do Utilizador

Z-3080CCD Barcode ScannerMulti-InterfaceUser’s ManualZBA Inc 94 Old Camplain Road Hillsborough NJ 08844Phone: 908-359-2070Fax: 908-359-1272Web: ht

Start of Configuration DATA REDUNDANT CHECK The option allows you to set decoder data redundant check. Enable Disable INTER-MESSAGE DELAY The

Start of Configuration SEND COMMAND IN BLOCK MODE COMMUNICATION You can use this option to set your own “Sen d” command used in block mode communi

INTERFACE CONFIGURATION 14 Start of Configuration 1. RS-232C SERIAL COMMUNICATION PARAMETERS SETTING The RS-232C scan

Start of Configuration ACK/NAK RESPONSE TIME SETTING (Cont’d) 3 sec 1 sec 5 sec BAUD RATE 19200 9600 4800 2400 1200 600 16 DATA

Start of Configuration MESSAGE TERMINATOR (FOR RS-232C TYPE ONLY) None CR/LF CR LF H Tab STX/ETX EOT 18 2. KEYBOARD EMULAT

Start of Configuration KEYBOARD TYPE SELECTION (Cont’d) NEC 9801 IBM 3196 Terminal APPLE MAC II(¡°) IBM 3477/3472 Terminal PS2/30/56 IB

MESSAGE TERMINATOR (FOR KEYBOARD WEDGE USE) None Return /Enter Hor. TAB Execute KEYBOARD TYPE SELECTION Scan Code Mode Alt mode BREAK C

Start of Configuration 00H~1FH ASCII Code defined Alt-mode code Crtl+code 3. WAND EMULATION PARAMETERS SETTING EMULATION SPEED SELECTION

Start of Configuration 4. USB INTERFACE PARAMETERS SETTING The USB mode is effectively a keyboard emulator that works with hosts that USB-compatib

Start of Configuration READING CODE SELECTION Code 39 Enable Code 39 Disable Coda bar Enable Coda bar Disable UPC/ EAN/ JAN Enable UPC/ EAN

NOTICE The issuer of this manual has made every effort to provide accurate information contained in thismanual. The issuer shall not be held liable fo

Start of Configuration READING CODE SELECTION (Cont’d) Italian Pharmacy Enable Italian Pharmacy Disable CODE 39 PARAMETERS SETTING CHARACTE

Start of Configuration CHECK DIGIT NO Calculate and Transmit Calculate but not Transmit CHINESE POST CODE PARAMETERS SETTING LENGTH MAX

Start of Configuration UPC/EAN/JAN PARAMETERS SETTING (Cont’d) EAN-13 EAN-8 ADDENDUM NO 5 Characters 2 Characters 2 or 5 Characters F

Start of Configuration TRANSMIT UPC-E CHECK DIGIT Yes No TRANSMIT EAN-13 CHECK DIGIT Yes No TRANSMIT EAN-8 CHECK DIGIT Yes No

Start of Configuration CODE 128 PARAMETERS SETTING (Cont’d) CHECK DIGIT No Calculate but not Transmit Calculate and Transmit UCC/EAN128 PAR

Start of Configuration MSI/PLESSY PARAMETERS SETTING (Cont’d) PLESSY CODE SETTING Calculated and transmitted Calculate but not transmitted CHE

Start of Configuration ISBN/ ISSN CONVERSION The function convents the UPC/EAN codes appearing on books and magazine not ISBN/ISSN format. ACTIVE

Start of Configuration HEADER AND TRAILER This option allows you to append a header and/or a trailer to every message transmitted via the serial po

Start of Configuration BARCODE IDENTIFIER CODE SETTING (Cont’d) Coda bar Code 39 Code 128 Code 93 MSI MATRIX 25 Set 46 Tru

APPENDIXES 48 APPENDIX A CODE 39 FULL ASCII CODE TABLE ASCII CODE 39 VALEUR HEXA. ASCII CODE 39 VALEUR HEXA. NUL %U 00 % /E

INSTALLATIONKeyboard Wedge 1. Turn off the PC2. Disconnect the keyboard cable from the PC. 3. Connect the Keyboard Cable to the scanner and connect

APPENDIX A CODE 39 FULL ASCII CODE TABLE ASCII CODE 39 VALEUR HEXA. ASCII CODE 39 VALEUR HEXA. J J 4A e +E 65 K K 4B f +F 66 L L 4C g +

APPENDIX B CODE 39 FULL ASCII BARCODE TABLE Start of Configuration NUL ENQ (Up) SOH (Ins) ACK (Down) STX (Del) BEL (Left) ETX (Hom

APPENDIX B CODE 39 FULL ASCII BARCODE TABLE Start of Configuration SYN (F6) GS (ESC) ETB (F7) RS Ctl (L) CAN (F8) US Alt (L) EM (F9)

APPENDIX B CODE 39 FULL ASCII BARCODE TABLE Start of Configuration 2 : 3 ; 4 < 5 = 6 > 7 ? 8 @ 9 A 56 APPENDIX

APPENDIX B CODE 39 FULL ASCII BARCODE TABLE Start of Configuration P W Q X R Y S Z T [ U \ V ] 58 APPENDIX B CODE 3

APPENDIX B CODE 39 FULL ASCII BARCODE TABLE Start of Configuration l s m t n u o v p w q x r y 60 APPENDIX B CODE

APPENDIX C BARCODE SAMPLES Code 39 C O D E 3 9 Code 128 C O D E 1 2 8 Interleaved 2 of 5 1 2 3 4 5 6 7 8 9 0 Coda bar(NW-7) A $ 9 9 . 9 5 A U

TABLE OF CONTENTS Introduction... 1 Default Parame

Chinese Post Code Parameters Setting...32 UPC/ EAN/ JAN Parameters Setting ...33 Coda bar/ Monarch Parameters Setting...

3. DEFAULT PARAMETERS This table gives the default settings of all the programmable parameters. The default settings will be restored whenever the

DEFAULT VALUES OF DECODING PARAMETERS Function Code Default Value Code 39 Enable ITF 2 of 5 Enable Chinese Post Code Disable UPC/EAN/JAN

SYSTEM SETTING 6 Start of Configuration RESET Ÿ The reading of the "RESET” label turns all the par

GENERAL CONFIGURATION 8 Start of Configuration SCANNING MODE SELECTION (for laser scanner) For series laser scanners, the